Busy few weeks..

Unfortunately not car related...had loads on with work and next weekend I am away at a 30th birthday party (seems to be lots of those recently!).

I've had nothing but hassle with the wife's mini one - I've spent 8 hours today on another fix.  Its leaking coolant, this time I think its the oil filter housing gasket.  I hope so, because if not I am out of ideas.  Looking at the old gasket it was "melted" flat and very brittle, evidence of coolant leak all around but that could simply be from the work I have previously done with the thermostat housing.

Anyway - kit car related, short on funds.  The drivers side panel is on, I've removed the clamps and all looks good but a fair bit of overspill from the "black tar of death" needs cleaning off the chassis.  I may see if I can get the other panel glued up before the end of the week....

The Kit Spares wish list is a good addition to their website, although it is dangerous.  A new wiring harness + fuel tank means I could potentially finish the rear end.....hmm.

Meanwhile, Jess is still helping every now and again:

Drivers Side Panel

After discovering that the inside crescents aren't part of the standard kit (seems a little daft - what does the carpet attach to?) I decided to crack on with the Drivers Side Panel.  People say different things, but for me I am going to put both panels on now.  I am not too bothered about how difficult it makes the rest of the build, apparently it makes it fiddlier to put the engine in - more of a challenge!.   Anyway, decided to put some selective rivets at the front, rear, underneath and on the top:

The panel fits perfectly already apart from a small piece I needed to file down at the top because I have already fitted the pedal box, easy enough with my new files:

The glue is horrible stuff, its easy enough to work with but impossible to get off your hands and clothes (although Coke seems to work well).  Once on I used lots of clamps, a ratchet clamp as well as some ingenious use of electic cable, screwdriver and a old hover cable - that's right, organised as ever.  Did the job though:

There's enough pressure all over to ensure the panel touches the chassis and its now sat for 24 hours till it goes off.  I will need to clean up the chassis where some of the glue has squeezed out, that should be easier to do once dry (I hope!).

Fuel Lines, Tidy Up and Diagram

Following on from the last post, I purchased a small sheet of Aluminium after deciding I was going to make my own bracket for the swirl pot as it looked too messy and I wasn't happy.

First I made a template out of cardboard and then transferred onto the aluminium, the template doesnt look like much but what you can't see is it folds over to give me something to attach to the next panel with. Cutting was easy as my father in law lent me some huge scissors which cut through with ease without too much distortion:

 

Photos are a little blurry I am afraid, not sure why.  You can see my new Clecos on the right, not really needed on such a small panel but any excuse to try a new toy!  They will definitely come in handy when I do some of the larger panels.  I also stuck the panel down with sikaflex to seal it up, I think its probably overkill but the end result is much better:

 Next was the fuel pipes, I decided to put some flexi-pipe wherever the lines crossed the chassis.  Looking at a few other blogs and the GBS recommendations, it was a little confusing exactly where I needed to put flex-pipe to meet the IVA requirements but I figure more is better.  I definitely need it at the rear around the handbrake cable and out towards the diff, but I wasn't entirely sure about the front so put a small piece where the pipes could potentially rub against the chassis.  Everything is secured with cable ties either side of each P clip:

Finally I mounted the high pressure fuel pump with two 60mm exhaust brackets, that seems to be the norm.  I was going to put a small piece of rubber between the pump and brackets but that doesn't seem necessary.  

 

You'll notice that I have riveted the swirl pot panel on, but rivnutted the actual swirl pot into the new bracket so it can be removed if needed later on.  Much neater I am sure you will agree and lots of progress made today.

Finally here is a diagram of how I think the fuel system is cabled, most of this comes from research on other peoples blogs and research - its starting to make more sense to me now, I still need to research more on how the swirl pot works but I think I have the cabling correct:

Next I am going to do the rear passenger crescent and side panels.  I have one more tube of sikaflex, should be enough but will likely need to order another tube afterwards.

Fuel System - Rear

After a long weekend away at the Silverstone grand prix (awesome!) I came back itching to do some work on the car.  I've been busy buying lots for the fuel system, thats what I am going to do next to get more of the rear finished off.

I am not 100% happy with two things, the first is the height of the low pressure filter- its probably me being too much of a perfectionist, but it didnt come with any kind of adapter or mount so its a different level than the pump.  I'm sure its not a problem:

 

 Jubliee clips came with the pump, but Ive purchased a load along with some 7.6mm and 10mm (not sure if thats right - need to check) R9 fuel pipe.  Next was to mount my new swirl pot, the second thing I am not happy with.

I had to change the bracket to the opposite side to fit - the issue with this is one of the rivnuts seems to have threaded, its not the end of the world (rock solid) but I will take anoher look after I have recovered from my weekend away:

Finally I need to sort out some piping to cover the fuel lines near the handbrake cable and out the rear, as per GBS instructions.  Not done a great deal today, too tired so giving it a miss till tomorrow.

Oh and one thing I want to do is some research on the fuel system.  I am trying to make sure I dont simply bolt things together - I want to understand as much as possible as I go through.  For example, I know what a swirl pot is for, but I dont understand how it works.